Business Products > Managed Switches > M4200 Intelligent Edge Series


Netgear M4200 Intelligent Edge Series


Netgear M4200 Intelligent Edge Series

Manufacturer

— Netgear

SKU

— M4200 Series

Description

Netgear ProSAFE® M4200 Intelligent Edge Series was designed from the ground up to optimize the installation of Wave 2 11ac access points.

Features

  • Advanced Layer 2, Layer 3 and Layer 4 security features
  • NETGEAR ProSafe Lifetime Hardware Warranty

Share this product

Enquire about this product

Netgear ProSAFE® M4300 Intelligent Edge Serie

ProSAFE® M4200 Intelligent Edge Series

Wave 2 11ac Access Point deployment

The world’s first Multigigabit Ethernet switch with eight full power PoE+ and multi-speed 1G, 2.5G ports combined with two 10G uplinks for a fully non-blocking deployment of eight Wave 2 11ac access points from any vendor.


The NETGEAR ProSAFE M4200 Intelligent Edge Series

8-port full power PoE+ of Multigigabit Ethernet line-rate connectivity.

NETGEAR ProSAFE M4200 Intelligent Edge applications

With 802.11ac, wired network must expand its reach and capacity.

What sets M4200 Intelligent Edge Series apart?

You can place this switch to optimize access point placement.


The ProSAFE® M4200-10MG-PoE+ Managed Switch was designed from the ground up to optimize the installation of Wave 2 11ac access points. Includes eight full power PoE+ and multi-speed 1G, 2.5G ports for 100 meter legacy cable runs, combined with two 10G uplinks for a fully non-blocking deployment of eight Wave 2 11ac access points. Two of these eight 1G, 2.5G PoE+ ports also support 5G speed. NETGEAR Multigigabit Ethernet is compatible with most major wireless and switching vendors managed solutions, and the only one with 8x2.5G to the AP with 240W PoE available and 2x10G line-rate aggregation to the wiring closet. Plenum rated, slim design and mounting accessories allow you to place this switch to optimize access point placement and cabling efficiency, inside and outside the rack..


Multi-Gigabit Ethernet

  • The ProSAFE® M4200-10MG-PoE+ comes with NBASE-T compliant 1G/2.5G/5G ports and 8 x 2.5G / 2 x 10G wire speed aggregation
  • That is, a purely line-rate access layer for 802.11ac wireless access points with PoE+ full provisioning, and ready for Wave2 3x3 and 4x4 installations

Higher flexibility

  • Plenum design with Easy Mount options whether it's directly on a wall, attached to a rectangular or round pole, or mounted in a standard 19-inch rack
  • Secure placement above drop-down ceilings, in air passageways and where other switches will not go, vertical or horizontal, flat or perpendicular

Lower complexity

  • Entire feature set including L2 switching (multi-tiered access control) and L3 routing (static, RIP, OSPF, VRRP, PIM, PBR) is available without license
  • DHCP/BootP innovative auto-installation including firmware and configuration file upload automation

Investment protection

  • Multi-Gigabit NBASE-T enables 2.5X to 5X faster speeds up to 100m on legacy Cat5e/Cat6 cables - yet providing 100M and 1G backward compatibility
  • Even if an organization is not ready for SDN, OpenFlow support offers future-ready design for maximum investment protection

Secure services

  • With successive tiering, the Authentication Manager allows for authentication methods per port for a tiered authentication based on configured time-outs
  • With BYOD, tiered Dot1x -> MAB -> Captive Portal authentication is powerful and simple to implement with strict policies

Industry standard management

  • Industry standard command line interface (CLI), functional NETGEAR web interface (GUI), SNMP, sFlow and RSPAN
  • Single-pane-of-glass NMS300 management platform with centralized firmware updates and mass-configuration support

Industry leading warranty

  • NETGEAR M4200 series is covered under NETGEAR ProSafe Lifetime Hardware Warranty
  • 90 days of Technical Support via phone and email, Lifetime Technical Support through online chat and Lifetime Next Business Day hardware replacement

Key features:

  • 1G, 2.5G and 5G NBASE-T compliant access layer in campus LAN and midsize organizations networks
  • Line-rate 8 x 2.5G access layer and 2 x 10G aggregation for 802.11ac wireless access points with PoE+ full provisioning
  • Advanced Layer 2, Layer 3 and Layer 4 feature set including static routing and RIP dynamic routing
  • Multi-Gigabit NBASE-T enables 2.5X to 5X faster speeds up to 100m on legacy Cat5e/Cat6 cables - yet providing 100M and 1G backward compatibility
  • Whisper quiet 28.9dB acoustics when operating at 25°C (77°F), well below normal offices ambient background noise
  • Secure placement above drop-down ceilings, in air passageways and where other switches will not go, vertical or horizontal, flat or perpendicular
  • Easy Mount options whether it's directly on a wall, attached to a rectangular or round pole, or mounted in a standard 19-inch rack
  • PoE+ (30 watts per port) across all (8) Multi-Gigabit access ports with 240W budget
  • Low latency and scalable table size with 16K MAC, 1K ARP/NDP, 1K VLANs, 64 routes
  • SDN-Ready OpenFlow 1.3 support for maximum investment protection

Software:

  • Advanced classifier-based, time-based hardware implementation for L2 (MAC), L3 (IP) and L4 (UDP/TCP transport ports) security and prioritization
  • Selectable Port-Channel / LAG (802.3ad - 802.1AX) L2/L3/L4 hashing for fault tolerance and load sharing with any type of Ethernet channeling
  • Voice VLAN with SIP, H323 and SCCP protocols detection and LLDP-MED IP phones automatic QoS and VLAN configuration
  • Efficient authentication tiering with successive DOT1X, MAB and Captive Portal methods for streamlined BYOD
  • Comprehensive IPv4/IPv6 static and dynamic routing including Proxy ARP, OSPF, Policy-based routing and automatic 6-to-4 tunneling
  • Enhanced IPv4/IPv6 multicast forwarding with IGMPv3/MLDv2 ASM and SSM Proxy and Control Packet Flooding protection
  • High performance IPv4/IPv6 multicast routing with PIM timer accuracy and unhandled PIM (S,G,rpt) state machine events transitioning
  • Advanced IPv4/IPv6 security implementation including malicious code detection, DHCP Snooping, IP Source Guard protection and DoS attacks mitigation
  • Innovative multi-vendor Auto-iSCSI capabilities for easier virtualization optimization

Availability:

  • Link Dependency new feature enables or disables ports based on the link state of different ports
  • Per VLAN Spanning Tree and Per VLAN Rapid Spanning Tree (PVSTP/PVRSTP) offer interoperability with PVST+ infrastructures

Management:

  • DHCP/BootP innovative auto-installation including firmware and configuration file upload automation
  • Industry standard SNMP, RMON, MIB, LLDP, AAA, sFlow and RSPAN remote mirroring implementation
  • Service port for out-of-band Ethernet management (OOB)
  • Standard RS232 straight-through serial RJ45 and Mini-USB ports for local management console
  • Standard USB port for local storage, logs, configuration or image files
  • Dual firmware image and configuration file for updates with minimum service interruption
  • Industry standard command line interface (CLI) for IT admins used to other vendors commands
  • Fully functional Web console (GUI) for IT admins who prefer an easy to use graphical interface
  • Single-pane-of-glass NMS300 management platform with mass-configuration support

NETGEAR Warranty

Build a secured, converged network with all types of traffic by preventing external attacks and blocking malware while allowing secure access for authorized users.

  • This product is backed by a NETGEAR ProSAFE® Lifetime Hardware Warranty.
  • Lifetime Next Business Day Hardware Replacement. Click here for coverage, availability and terms and conditions.
  • ProSUPPORT 24x7 Advanced Technical Support via phone for 90 days (Remote diagnostics performed by our technical experts for prompt resolution of technical issues). ProSUPPORT coverage can be extended by purchasing one, three, or five year contracts.
  • ProSUPPORT Lifetime 24x7 Advanced Technical Support via chat. (Remote diagnostics performed by our technical experts for prompt resolution of technical issues).





Specifications



Netgear Business Network solution
Full Power PoE+ 8x2.5G and 2x10G Aggregation Switch For Wave 2 11ac AP Deployment
Part Number M4200-10MG-PoE-Plus
Acoustics Whisper quiet 28.9dB @ 25°C (77°F)
Power Consumption (Max) 281.6 Watts @ full PoE+
RJ45 Ports 8 x 1G / 2.5G including two of these ports with 5Gbps capability
10G Fiber SFP+ Ports 2 x SFP+ (1G and 10G speeds)
Power over Ethernet 8 x PoE+ 30W ports
PoE Budget (Watts) 240W
Feature Set Layer 3 (static routing and RIP dynamic routing)
Management Ports
  • 1G Ethernet service port for out-of-band management (OOB, RJ45)
  • RS232 straight-through serial RJ45 for local management console
  • Mini-USB port for local management console
  • USB port for local storage, logs, configuration or image files
Form Factor Easy Mount for standard rack mounting and plenum mounting on poles or walls



Kaira Technologies © Copyright 2015, All Rights Reserved